Well, yum, yum, and yum. Look at what the latest 3D printing genius has dropped off on the kitchen doorstep for all those technologically savvy and daring chefs. Who could resist? While the industry is pumping out one incredible 3D printed innovation after another–many of which are amazing and interesting with the capability to change the world and even save lives–nothing captivates the attention span like icing. That’s because, quite simply, we know what comes with it: cake.
Instructables member bravoechonovember brings you the Icing 3D Printer–now all you have to do is find something to adorn with sugary delight. Bravoechonovember does say that while this is a tool that allows you to do something fun and easy, creating the printer was anything but.
“This was one of the hardest projects I have built,” said bravoechonovember. “Throughout the project I broke two arduinos, 2 stepper motors, and I lost the plunger for the eyedropper, so if you see something different it probably is different.”
Following the Instructable and learning from the mistakes of the original builder should lead to much greater success with this 3D printer that’s a little on the alternative side (as is much in the making tinkering community).
“I know everyone is going to say that isn’t a 3D printer if it doesn’t have a Z axis!” states bravoechonovember. “But there is enough space to build up something three quarters of an inch.”
The parts list is fairly simple and doesn’t appear to be terribly expensive, as follows from the designer:
- Arduino Uno LINK
- Motor/stepper/servo shield LINK
- Two DVD readers
- Electrical wire
- Sheet metal (I used aluminum)
- Icing
- Something to ice
- Superglue
- Eyedropper (the plastic kind)
- Pop rivets (or any other fastener)
- Plastic feet
- Tools
- Soldering iron
- Solder
- Wire Cutters
- Screwdriver
- Pop rivet gun–only if choosing to use pop rivets
- Drill
- Drill bit–to be the size of your pop rivets or fastener
Once you’ve got your parts lined up, you’ll want to start with following the instructions to take the two DVD readers apart, unscrewing them and basically working to extract the metal piece in the middle easily, as it should lend itself to being pulled right out. With that set, it’s time to build the frame, which is very simple as well, consisting of only a few steps.
The frame is ready to go after bending a small piece of sheet metal and installing it to the top of the DVD reader in several easy steps to include some use of the drill and subsequent fastening. The sledge holders are attached to the top and the bottom, and may require extra stability with an extra U-shaped piece.
Once the printing plate and the eyedropper nozzle are glued on, electronics and code come next. You’ll need to solder wires on and attach them to the Arduino, after which you’ll need some software, which is recommended in the Adafruit example library under the section for multiple motor steppers.
“This was my first Arduino project so I didn’t code very much,” explained bravoechonovember. “I just edited the speed of some example code.”
And finally–the next step is what we’ve all been waiting for: prepare to get down with some 3D printed icing. Using a small amount of heated icing to fit into the eyedropper, fill it to capacity and push the plunger down and start the Arduino.
“I found that putting the microwaved icing in a plastic bag with a hole cut in the end and squirting it into the eyedropper doesn’t make a big mess,” adds bravoechonovember.
And with that, you can enjoy both your new 3D printer and a new hobby that includes icing everything in sight. Both the DIY 3D printer and what it extrudes should make not only for great dessert, but an excellent conversation piece as well.
Are you considering making this 3D icing printer, and if so, did you encounter any of the same initial assembly challenges as bravoechonovember? Discuss in the 3D Icing Printer forum thread over at 3DPB.com.
If you're looking to get architectural 3D animation in the USA, our service provides an exceptional way to bring your architectural concepts to life through dynamic, immersive visuals. Through our platform, you can easily request high-quality 3D animations that showcase your designs in motion, offering a detailed view of your project from multiple angles and perspectives. Whether it's for a real estate development, a commercial building, or an urban planning project, our expert team ensures that every detail is captured in a visually compelling animation.
Through our website, you can seamlessly get architectural 3D animation tailored to your project’s specific needs. With our help, you can offer potential clients or investors an engaging experience that goes beyond static images. By integrating CGI animations with real-world settings, lighting, and textures, our team creates a lifelike experience that allows your audience to interact with your project as though it were already built. This service is perfect for presenting complex designs in a clear, visually attractive way that stands out in the competitive architectural market.
